KAVASSU GROUT – EHS

Home / KAVASSU GROUT – EHS

Ultra Strength Free Flow Non-shrink Grout

KAVASSU GROUT -EHS is composed on specially processed cements containing micro silica and additives. KAVASSU GROUT -EHSis supplied as a ready to use grout requiring addition of precise quantity of water at site @0.170 for pourable Consistency and 0.175 for flowable consistency. (4.25 Liters / 25kg grout). KAVASSU GROUT -EHS has excellent flow properties and will not shrink after placing and it is suitable for gap widths of between 15mm 65mm. Due to its selfleveling property, it is easily flows to reach the un reachable portion of the area for placing. It gives High early strength with pre plasticized action property.

  • Manufactured controlled, ready to use with only proportioned water.
  • Shrinkage offset by expansion to ensure original volume is retained.
  • Free flowing with self leveling grout properties.
  • Easy to place and filling of under bases of machinery as well as bolt pockets.
  • Chloride free to avoid further climatically attack.

Bolt pocket and baseplate grouting of all equipments, heavy machineries, stanchion bases and all types of machinery in cement, textile, paper, steel industries, etc.

General

KAVASSU GROUT -EHS is composed on specially processed cements containing micro silica and additives. KAVASSU GROUT -EHSis supplied as a ready to use grout requiring addition of precise quantity of water at site @0.170 for pourable Consistency and 0.175 for flowable consistency. (4.25 Liters / 25kg grout). KAVASSU GROUT -EHS has excellent flow properties and will not shrink after placing and it is suitable for gap widths of between 15mm 65mm. Due to its selfleveling property, it is easily flows to reach the un reachable portion of the area for placing. It gives High early strength with pre plasticized action property.

Advantages
  • Manufactured controlled, ready to use with only proportioned water.
  • Shrinkage offset by expansion to ensure original volume is retained.
  • Free flowing with self leveling grout properties.
  • Easy to place and filling of under bases of machinery as well as bolt pockets.
  • Chloride free to avoid further climatically attack.
Uses

Bolt pocket and baseplate grouting of all equipments, heavy machineries, stanchion bases and all types of machinery in cement, textile, paper, steel industries, etc.

Application Procedure

Bolt Pockets :
Depending on the size of the bolt pockets, 50-100% cleaned 10mm baby aggregates by weight of grout consumption may be incorporated to economize on grout and also to keep the heat of hydration low. When the thickness exceeds 100mm 150mm, our technical department may be contacted for advice. There must be at least 15 hours gap between bolt pocket and under base plate grouting sequences.

Base plates :
Leak proof strong form work must be provided to withstand operational stresses while grouting and all edges must be sealed with KAVASSU GROUT -EHS troweling consistency to arrest the grout from flowing out of form work. The sealed edges must be strong enough to resist.

Surface Preparation :
1. All contaminated surfaces must be cleaned thoroughly and all contaminations fully removed by chemical or mechanical methods.
2. All bolt pockets and under bases must be free from dust, laitance and of sound substrate. If needed, substrate must be hacked to provide extra mechanical key.
3. The pockets and under bases must be inundated with water to allow for full absorption for at least 24 hours. Just before the grouting is to commence, all water must be removed completely leaving the surface only damp.

Mixing :
Mechanical mixing using a grout mixer or concrete mixer is only recommended. No hand mixing is permitted.
1. Place 80% of the water required in a concrete mixer (100% water in case of a grout mixer).
2. Slowly add the required amount of KAVASSU GROUT -EHS while mixing continuously for 1 minute. Add balance quantity of water (20%) and mix for 3 to 5 min.max.

Placing :
The mixed grout must be placed immediately from one side only to avoid air pockets. Hydrostatic head of 150-250mm must be provided to enable the free flowing of grout under base plate. Grouting must be continuous until the cavity is completely filled to the desired level. All exposed areas must be restrained by covering with wooden plates or polythene sheets with sand sprinkled on top of the sheet.

Curing :
12 hours after grouting, all grouted areas must be cured with wet Hessian cloth (keep wet always) or water ponding wherever possible for a minimum 7 days period. Cleaning: All equipment and tools must be rinsed with water immediately after use and then dried.

STORAGE LIFE :
KAVASSU GROUT -EHS has a minimum shelf life of 6 months if stored in a dry enclosed area in unopened bags.

HANDLING PRECAUTIONS :
KAVASSU GROUT -EHS is non-hazardous. However inhalation of dust should be avoided while handling. In its wet state, if contact.

National Award Winner

Yield : One pack of 25 Kg KAVASSU GROUT -EHS will yield approximately 13 litres of grout when mixed with specified quantity of water.

Packaging : 25 kg bags, 50 kg bags

Applicable Temperature : May be applied in between 100C – 350C

Expansion (% By Volume) : 0.9 – 1 %

Density : 2220kg/m3

As per ISO-9001 Certification.

If swallowed seek medical advice.

25 Min after adding water.

The compressive strength of KAVASSU GROUT -EHS tested under restrained conditions using 7.07cm cubes.

Features

Yield : One pack of 25 Kg KAVASSU GROUT -EHS will yield approximately 13 litres of grout when mixed with specified quantity of water.

Packaging : 25 kg bags, 50 kg bags

Applicable Temperature : May be applied in between 100C – 350C

Expansion (% By Volume) : 0.9 – 1 %

Density : 2220kg/m3

Quality Assurance

As per ISO-9001 Certification.

Health & Safety

If swallowed seek medical advice.

Pourable Life

25 Min after adding water.

Strength Development

The compressive strength of KAVASSU GROUT -EHS tested under restrained conditions using 7.07cm cubes.

WE OFFER MORE POSSIBILITIES

TO MEET YOUR EVERY NEED

What Clients Say