PROFILE | PRODUCTS | NEWS ROOM | CREDENTIAL    
 

Product  

WATERPROOFING COATINGS
PRODUCT DESCRIPTION APPLICATION AREA METHOD OF APPLICATION
SHALIMAR SEAL
 (20 Kg.) 		SHALIMAR SEAL (Leak proof Chemical Compound) is a dispersion of selected grades of Resins, Oils & Polymers with inert fillers & selected fibers. It creates a tough & abrasion resistant film, seals hairline cracks totally & acts as an effective barrier against moisture, water & atmospheric impurities. It waterproofs all absorbent surfaces.
 ADVANTAGES : Abrasion resistance, washable, scrub resistance. High elongation, withstands expansion/ contraction without cracking, deforming, softning or peeling of films. Excellent adhesion to almost all types of structures & building materials. Excellent barrier against moisture, water & atmospheric impurities. Prevents growth of fungus, mildew, algae etc. No skilled labors required. Can be applied by brush.		 Waterproofing of RCC / Lime Terraced roofs, Sunken Portions of bathrooms, External & Internal walls of Basement, Floor surface of basement, & also recommended for use on sloping roofs, domes, steeples, bio gas plant, shell roofs etc. Roof top leakages through cracks developed in the roof slab due to expansion & contraction by temperature variation / mud sinking in RCC, PCC, mud phaska, bricks tiles, lime terracing, stone slab roofing. The parapet wall / roof surface has to be cleaned fully relieving of loose particles, dust, oil, grease, wax, dirt or any other form of foreign matter with help of wire brush /fine brush. After cleaning of the entire surface the Chemical compound SHALIMAR SEAL becomes in molten condition to be spread or paint all over the surface with the help of rubber spreader or fine paint brush @ 650 Gms. per Sqm.
SHALIMAR SEAL - EHD
 (20 Kg.) 		A conglomerated equipoise of multi-pronged virtues, a non wearing way, decomposing ineffaceable basic off shoots of mineral hydrocarbons, an amalgamated fusion of truly balanced, closely varying low pour points non-crystalline compound polymers, formed into an all weather permanent filler and for complete coverage of leaking tractates in the roofs for negated water leakages and thus, a net result of conscious persuasion to leaking hazards. SHALIMAR SEAL - EHD is complete post positional cure of architectural or natural dishevelment. The compound penetrates into the smallest possible holes and then settles itself forever. It may be used over the roof where Glazed Tiles/ Mosaic Tiles/ Fancy Tiles/ Marble Tiles, as it is cream in Color or say it is colorless. The roof can be used after sometime as previous, Roof top leakages through cracks in RCC, PCC, mud phaska, bricks tiles, lime terracing, stone slab roofing. First scrape and clean the place & Large holes and cracks should be plugged with mixture of cement, sand and water. The roof should be dry at the time of SHALIMAR SEAL - EHD application. Now sufficiently spread a thin layer of the molten hot liquid all over the surface or block @ 650 Gms per Sqm. of SHALIMAR SEAL - EHD depending upon the porosity of the surface including the parapet tops by Gardener's shower or rubber spreader. This spread liquid thus packs up the tracks of leaking, penetrates into smallest possible holes and then settles forever.
U-SEAL
 (20 Kg.) 		U- Seal” waterproof compound is based on latest research and technological developments. It permeates into surface to make it highly waterproof and heat proof. “U- Seal” is based on Silica, Hydrocarbons, high performance resins, polymers etc. that provides a highly water repellent finish. They are unaffected by heat and cold. Bricks Tiles or Brick Coba or 50 mm cement concreting any one of these treatments must be done over the U- Seal treatment. For use in newly constructed buildings over Reinforced & Plain Cement Concrete. After cleaning of the surface large holes and cracks should be plugged by cement, sand and water. After opening the mouth of the drum of “U- Seal”. Do not alter or add any foreign material to “U- Seal”. Apply a coat of “U-Seal” @ 750 Grams per Sqm. By paintbrush or rubber brush. Apply the second coat @ 500 grams per Sqm. when the first coat is totally dry, or after 12 hours under normal conditions.
CALTEX SEAL (TYPE- B)
 (20 Kg.) 		CALTEX SEAL TYPE- B is a dispersion of a selected grade of polymers, asphalts & resins with inert fillers. Selected fibers are used as fillers to form a surface, resistant to considerable shock and vibrations. A coating, when set is impermeable to water and shows a marked resistance to variation in climatic conditions, industrial fumes and salty atmospheres. Leakage caused through cracks. It effectively protects against concrete decay. If there is a likelihood of rain intervening with the CALTEX SEAL TYPE- B coating, work should be deferred. When the surface is cleaned completely, apply CALTEX SEAL TYPE- B in two coats with a brush or a trowel @ 1 kg. Per Sqm. Per coat. No water should be added to CALTEX SEAL TYPE- B when applied as a coating. After the final coating when CALTEX SEAL TYPE- B turns black, spread dry coarse sand at 0.06 cu. meters per 10 Sqm.
W -SEAL
 (20 Kg.) 		Based on quality wax, complex organic chemicals & rich minerals is a brushable liquid.
 ADVANTAGES :

 Single Component, ready-to-use. Excellent use to all surfaces (RCC/ Plastered/ Lime Terraced/Cement Concrete). No skilled labor required. Economical and durable.		 For water proofing of terraces parapet walls, and chajjas, of (RCC/ Plastered/ Lime Terraced/ Cement Concrete). Clean the surface relieving of dust, loose particles, oils & grease etc. Fill the cracks with CAPITEX CRACK FILLER compound with knife/spatula & allow drying for 24 hrs. Apply first coat of W - SEAL on prepared surface @ 500 Gms. Per Sqm. By paintbrush. Allow drying for 12 hrs. or overnight. Apply second coat of W - SEAL @ 500 Gms. Per Sqm. by paintbrush.
CAPIKOTE TYPE- 10
(20 Kg.) 		It is water bound Emulsion with finely divided Bitumen dispersed in water of paste like consistency brown in Color & ready for application on damp surfaces. The main purpose is to avoid heating of Bitumen at site, before application as well as to overcome the handicap due to wet surfaces, when bituminous materials are to be applied. CAPIKOTE TYPE- 10, is also recommended for use on porous roof & walls as per the specification given. CAPIKOTE TYPE- 10, should not be applied when there is likelihood of rain wetting the surface before the CAPIKOTE TYPE- 10, breaks completely. As far as possible, walking over the treated surface should be restricted to the minimum. Clean the roof surfaces thoroughly with Wire brush and to remove all loose particles. Reduce CAPIKOTE TYPE- 10 by adding soft (drinking) water. Apply this paint on the roof surface as primer liberally. After drying of primer, apply CAPIKOTE TYPE- 10, slightly reduce with water, @ approximately 1.5 Kg. per Sqm. & allow the emulsion to break. Application should be in built up layers minimum 2 layers after prime coat, allowing between coats, sufficient time for setting. Dry film thickness built up should be minimum 3mm before spreading sand or pea size gravel.
CALTEX SEAL
 (20 Kg.) 		Leak proof chemical compound. Roof top leakages caused through cracks developed by expansion & contraction by temperature variation. After cleaning of the entire surface the Chemical compound should be spread or paint all over the surface with the help of rubber spreader or fine brush @ 650 Gms. per Sqm .
SHALILAFARGE - UKWC
 (20, 200 Kg) 		SHALILAFARGE - UKWC Is rubberized Modified asphalt emulsion. It is a cold applied, single component, which builds thick membrane on the processed surface. It is an excellent item for water proofing of concrete surfaces, walls, foundations, sunken portions etc. & compatible for protection of metal, wood & concrete against severe corrosive conditions. Clean surface dirt and grease from the surface. Use a soft-bristled brush or heavy duty spray machine & apply one coat of SHALILAFARG - UKWC over the surface @350 Gms / Sqm. After drying of 1st coat, apply 2nd coat of SHALILAFARGE - UKWC over the surface @350 Gms / Sqm.
CAPIKOTE TYPE- 32
 (20 Kg.) 		CAPIKOTE TYPE- 32 is a dispersion of selected grades of bitumen in water, with inert fillers. Selected fibers are used as fillers to form a surface, resistant to considerable shock & vibrations. A coating, when set, is impermeable to water & shows a marked resistance to variation in climatic conditions, industrial fumes and salty atmospheres.
 CAPIKOTE TYPE- 32 should not be applied under wet conditions. If there is a likelihood of rain intervening with the coating, work should be deferred.		 It is particularly recommended for waterproofing of roofs, reconditioning of roofs, etc. It provides a membrane of substantial thickness & plasticity. It can be worked into cracks & crevices. Clean the roof surfaces thoroughly with Wire brush & to remove all loose particles. Reduce CAPIKOTE TYPE- 32 by adding soft (drinking) water. Apply this paint on the roof surface as primer liberally. When the primer is dried completely, apply CAPIKOTE TYPE- 32 with a brush or a trowel @ 8Kg. per 10 Sqm. A min. of 2 coats is generally recommended. The film dries in 24 to 48 hrs. After the final coating, spread dry coarse sand at 0.06 cum /Sqm.
CAPIKOTE TYPE- 25
 (20 & 220 Kg.) 		CAPIKOTE TYPE-25 is colloidal clay types emulsion that is applied cold for protective purposes in thick coats and without flowing off at high temp. or losing ductility at low temp. The weathering properties of properly applied dried film are also better and offer many advantages over hot melts or solutions. It is particularly recommended for waterproofing of roofs, reconditioning of roofs, anti-corrosive painting over M.S Steel etc. It provides a membrane of substantial thickness and plasticity. It can be worked into cracks & crevices. CAPIKOTE Type- 25 should be applied on pipes, which have been thoroughly cleaned & primed with TANKMASTER (Confirms to IS: 158 1982) . It is applied over the roofs & vertical basement walls. It should be applied in 2 coats of equal thickness, for building up a dried film of 3 mm thick. Minimum 18 hrs. Should be allowed for proper drying of the 1st coat and then the 2nd coat is applied. 6 hrs. Minimum drying in open air should be allowed before any top wrapper (outer wrap tissue, craft paper, etc.) goes over the treatment.
FERRO GUARD
 (20 Kg.) 		FERROGUARD is a High Build Emulsion with the unique property of building a thick coating in single application without sagging. It is of heavy consistency and has higher strength and durability compared to other conventional systems. It will not form blisters or cracks on the dried film. The selected clay type filler in it imparts breathing quality to the bitumen film and prevents the flow of dried film. FERROGUARD is non - toxic and can be used in food stores & has the ability to develop high building coating, excellent resistance to moisture, and can be easily patched up if damaged. FERROGUARD is used for waterproofing of flat, sloped & steep roofs where cold and durable applications are preferred. It is also used for anticorrosive treatments for steel, concrete and other structures. It is a very effective coating particularly for alkaline atmosphere. Clean the roof surfaces thoroughly. One coat of FERROGUARD primer. One coat of FERROGUARD @ 1kg. Per m2. 2nd coat of FERROGUARD @1 Kg. per m2, top layer will be finished with coarse sand. Heavy Duty Treatment: Clean the roof surfaces thoroughly. One coat of FERROGUARD Primer. 1st coat of FERROGUARD @ 2 Kg. per m2. One layer of Fiberglass R.P. Tissue. 2nd coat of FERROGUARD @ 2 Kg. per m2. Screed or tile or coat of Aluminum shield or sand is to be spread.

CUSTOMER CARE SERVICE: +91-9829065184, 9829065284, 9810897384, 9810028937, 9314512969, 9414063757

Home | Contact US | Profile | Products | News Room | Credential